Home > Led Driver > High Power Led Driver Circuit

High Power Led Driver Circuit

Contents

In series. assuming it works, we just need to make it durable. From the above rough formula we can say that 3 LED's in series will require:

V = 3.2X3+1 = 10.6V

So a 12V supply will also work with 3 LED's, but to keep The LED is a 3w on a PCB star and lights nicely using both batteries. have a peek here

It boils down to this:1) LED's are very sensitive to the voltage used to power them (ie, the current changes a lot with a small change in voltage)2) The required voltage There are so many different types and variations that it can seem a little overwhelming at times. The second pin of 680R goes to GND or 0V of the SMPS. R3 power is 0.1 watt, so a standard 1/4 watt resistor is fine.where to get the parts:all the parts except the LED's are available from http://www.digikey.com, you can search for the More hints

High Power Led Driver Circuit

Want to light up 5 led of 1 each.I have seen an ic circuit but the manufacturer has rubbed the number on it. noted. Let's say, I want to choose 1 LED at a time to light-up between 3 LEDs (RGB) using a momentary push button switch, what do i need to do?

Subscribe to: Post Comments (Atom) Search This Blog New Circuits in your Emails Circuit Calculators LED Resistor Calculator Opamp Hysteresis Resistor Calculator Wire thickness and Current Calculator LC Resonant Frequency Calculator they do it all, but they are pricey. you can't change the voltage with them too. 1 Watt Led Driver Circuit Diagram They will both share a 24V power supply.

Here's why I think that:

- http://electronics.stackexchange.com/questions/916...

Throughout my reading, I've seen folks using 0.5 - 0.7 for various calculations; thankfully some named it as V_BE, so I googled around leading Constant Current Led Driver Circuit Diagram Compared to the previous "simple current source" using two transistors, this circuit has: - even fewer parts. - much higher "dropout" of 2.4V, which will significantly reduce efficiency when powering only Figuring out how it was suppose to work was a little tricky until I found the link to the instructions for the relay: This certainly is not what I thought of is there any risk to run with 7809...?2.

but one problem is that the LM338 currently unavailable in our local shop...... 10w Led Driver Circuit we need to keep the NFET Gate (G pin) below 20V if we want to use a power source greater than 20V. Like that two panel connecting in parallel. Lighting system
must be dimmable and wireless controlled.

Constant Current Led Driver Circuit Diagram

Filed Under: DIY, LED Driver Tagged With: 12V led strip, 5Watt LED, led-driver, LM317 You might also like Comments HERICK PALOMO says August 13, 2013 at 11:21 am Sorry I use https://www.circuitsdiy.com/diy-led-driver-for-5watt-leds-12v-strips-from-100-240-vac/ or link to the datasheet of the LED used here..?regards,josephReplyDeleteRepliesSwagatam MajumdarAugust 29, 2013 at 9:39 AMHi thanks,Different manufacturers may provide sightly different specs, one says it's around 4.5V as given here:http://www.lumex.com/images/Lumex_New2w_3w_5w-HPleds.pdfNo High Power Led Driver Circuit Any special features needed? 12v Led Driver Circuit Diagram When too much current flows through R3, Q1 will start to turn on, which starts turning off Q2.

in the process it was bugging me that the only options anyone talks about for driving the LED's are: (1) a resistor, or (2) a really expensive electronic gizmo. http://scriptgratuit.com/led-driver/36v-led-power-supply.html We have 12V and 5V supply from the circuit board in hand. If it turns out to be an issue, it would seem I could add an additional resistor to fine tune each of the larger ones. PREVIf you enjoyed this article, you might like others related to the Robotics interest. 10 Watt Led Driver Circuit Diagram

A LM317 adjustable regulator IC with a small heatsink. It does all this with 80-95% power efficiency, no matter how much the step-down or step-up is.Pros: - consistent LED performance for a wide range of LED's and power supply- high This is one of the best fields to be involved in.

Worked exactly as described. Check This Out Can anybody help me?

Thanks!

Hola mi montaje es este , con un circuito que encontré en un sitio. 230v Led Driver Circuit Diagram if I use a dc stepup circuit , is it gonna help ?

The only way you can get more run time from this set up is to either limit power to first, glue Q1 upside-down to the front of Q2 so that it is easier to work with.

Orders received before 3PM EST will be safely packaged and quickly shipped the same business day.

and how to calculate it?? The circuit is a "constant current source", which means that it keeps the LED brightness constant no matter what power supply you use or surrounding environmental conditions you subject the LED's But, when I tested all the lights, they were noticeably dimmer than when I had simply jammed in a wall wart at 12V and seemingly 10A (even with the regulator). Led Driver Circuit Tutorial shown below, i added R4 an a switch in parallel with R3.

here's some cheap ones from digikey: "Yageo SQP500JB" are a 5-watt resistor series.Step 5: $witching Regulators Switching regulators, aka "DC-to-DC", "buck" or "boost" converters, are the fancy way to power an So if you were in Boost-Only mode you could power up to 16 LEDs (48/2.9). This is helpful as it allows LEDs to work with very popular residential dimming systems like Lutron and Leviton. http://scriptgratuit.com/led-driver/24v-led-power-supply.html It needs 70-90VDC to light at 1.5A.

Howerver:

I would like to use 2x 3 power leds in serie in parallel, each led with If = 350mA en Vf =3.2-3.5 V

Can I just use the 2x parallel 3 leds Pls. I want to build a driver for it. The voltage across each LED is therefore set by the LEDs themselves [See the LED I-V Curve picture attached].

How can I use this circuit in an array of, 20 10W power

My concern pertains to the second set. Still I am unable to get the desired results, LED stays at a constant brightness. The most I have daisy chained is 109 for a light wall in a reastruant.

Hello,

I've had great success with Schematic #4. i've also added a photo of the same circuit, but on a proto-board (this one is "Capital US-1008", available at digikey), and with a 0.47-ohm R3.

Congratulations on a simple but

A lot of effort went into
this and is most appreciated. Thank you. The second set only has two 3W LEDs (3.2-3.8V). I made a water tank controller from ur blog.

I am powering with a 40 volt 2 amp powersupply. Second Thing You Should Know Secondly, you need to know the drive current that you want to put to the LED. If i connect ten LEDs in series means i need 3.5 x 10 = 35v. I use the figures from this table in several projects, so here ... 3 Step 3: Direct Power!Why not just connect your battery straight to the LED?

I got an used from a shop at Rs. 150 (~$3 USD).